“模板:How to use iODD”的版本间的差异

来自iODD
跳转至： 导航、 搜索
（创建页面，内容为“=== 基本职能 === ==== IODD的示例文件夹树 ==== :创建一个在根文件夹命名的文件夹 "_ISO" :此文件夹树就是一个例子 :"_ISO"下的任何...”）
 
Kbs（讨论 | 贡献）
第51行： 第51行：
 
# 启动密钥（启动时）
 
# 启动密钥（启动时）
 
#* 抬起<code>拨轮</code> - 在CD-模式启动
 
#* 抬起<code>拨轮</code> - 在CD-模式启动
−
#* Down <code>Jog-Dial</code> - Start up in HDD-MODE 向下拨轮 - 在HDD模式启动了
+
#* 向下<code>拨轮</code> - 在HDD模式启动了
−
#* Push <code>Jog Dial</code> - Reset loading state. Start up in DUAL-MODE
+
#* 按<code>拨轮</code> - 复位加载状态。双模式启动
−
#* Push <code>BackUp</code> Button - Start up in Write-Protected mode.
+
#* 按下<code>备份</code>按钮 - 在写保护模式启动。
  
−
==== 2541 Keys ====
+
==== 2541 钥匙 ====
−
# Navigation
+
# 导航
−
#* Up/Down list - <code>2</code> / <code>8</code>
+
#* 向上/向下列表 - <code>2</code> / <code>8</code>
−
#* Select file - <code>5</code> (or <code>6</code>, for maintaining loading state)  
+
#* 选择文件 - <code>5</code> (or <code>6</code>, 用于保持装载状态)  
−
# Menu
+
# 菜单
−
#* <code>Menu</code> - Go to Menu. (or Exit).
+
#* <code>Menu</code> -进入菜单。 （或出口）
−
#* <code>4</code> - Go to upper list
+
#* <code>4</code> - 转到上名单
−
# Long key ( push for 3 seconds )
+
# 长键（按3秒）
−
#* <code>1</code> - [[#Go to Power Saving State|Go to Power Saving State]]
+
#* <code>1</code> - [[#进入节能状态|进入节能状态]]
−
#* <code>3</code> - reboots iODD
+
#* <code>3</code> - 重新启动IODD
−
#* <code>4</code> - refreshes file lists
+
#* <code>4</code> - 刷新文件列表
−
#* <code>7</code> - Reboot. and detach all virtual drives (VHD, RMD, IMA)
+
#* <code>7</code> - 重启。和分离所有虚拟机（VHD，RMD，IMA）
−
#* <code>0</code> - Reboot. and Temporarily disable Write-Protection
+
#* <code>0</code> - 重新启动。并暂时禁用写保护
−
# There is not Startup key
+
# 没有启动密钥
  
−
==== Go to Power Saving State ====
+
==== 进入节能状态 ====
−
: Power Saving State : Spindle motor is stopped and LCD brightness is low.
+
: 省电状态：主轴电机停止，液晶显示器的亮度是低的。
−
: CD loading state is saved.
+
: CD装载状态被保存
−
* (2531) Down the <code>Jog Dial</code> for 3 seconds.
+
* (2531) 下<code>滚轮按钮</code>3秒钟
−
* (2541) Push the <code>1</code> button for 3 seconds.
+
* (2541) 按<code>1</code>键3秒
  
−
==== Selecting a file ====
+
==== 选择一个文件 ====
−
: In order to maintain loading state, you must save the state.
+
: 为了保持加载状态，你必须保存的状态。
−
: Refer to the above key operations.
+
: 参考以上的键操作。
−
* (2531) [[#2531 Keys]]
+
* (2531) [[#2531 钥匙]]
−
** If Firmware version is 1558 or higher, loading state is automatically saved.
+
** 如果固件版本为1558或更高，载荷状态会自动保存。
−
** If not, you must save it manually. ([[#Go to Power Saving State|Go to Power Saving State]])
+
** 如果没有，你必须手动保存. ([[#进入省电状态]])
−
* (2541) [[#2541 Keys]]
+
* (2541) [[#2541 钥匙]]
−
** If Firmware version is lower than 6(7)9-05, button <code>6</code> has no function.
+
** 如果固件版本低于6（7）9-05，按键6起不了什么作用
  
−
==== Safely Removal In OS ====
+
==== 安全去除OS ====
−
: If iODD's partition is NTFS, then this function is mandatory when disconnecting iODD from host.
+
: 如果IODD的分区是NTFS，然后从主机断开IODD时，此功能是必需的。
−
: NTFS does not write Immediately the data to HDD.
+
: NTFS不会立即将数据写入硬盘。
−
* Please do [http://windows.microsoft.com/en-US/windows7/Safely-remove-devices-from-your-computer Safely Removal] before disconnection.
+
* 断开连接之前请不要 [http://windows.microsoft.com/en-US/windows7/Safely-remove-devices-from-your-computer 拆除安全]
−
* If iODD is write-protected mode and an error message appears, then disable write-protect option. and retry this function.
+
* 如果IODD是写保护模式，并显示一条错误消息，然后禁用写保护选项。然后重试此功能。
  
 
=== Initialization ===
 
=== Initialization ===

2016年6月3日 (五) 16:09的版本

基本职能

IODD的示例文件夹树

创建一个在根文件夹命名的文件夹 "_ISO"
此文件夹树就是一个例子
"_ISO"下的任何文件名和文件夹名是可以接受的
J:
├─ _ISO
│  │  Hiren’s BootCD 15.2.iso
│  │  ubuntu-14.04.4-desktop-amd64.iso
│  │  Windows 10.iso
│  │  Windows XP sp3.iso
│  │  (32文件夹及文件夹中限制)
│  │  
│  ├─IMA for Floppy
│  │      Bios updater.ima
│  │      MS-DOS 6.0.ima
│  │      Symantec Ghost.ima
│  │      
│  ├─RMD for Setup
│  │      Win 7Ent_x86_x64+8.1Pro+10Pro vol2.RMD
│  │      Win7_Ult_SP1_Russian_x64.RMD
│  │      Windows 10.RMD
│  │      
│  └─VHD for Booting
│      │  linuxmint-17.3-cinnamon-32bit.vhd
│      │  Windows 10 Win2Go.vhd
│      │  Windows 7 OS Booting.vhd
│      │  
│      └─嵌套子文件夹允许
├─Your Folder 01
├─Your Folder 02
├─Your Folder 99
│  Your files 01.txt
│  Your files 02.txt
│  Your files 99.txt

2531 钥匙

  1. 导航
    • 向上/向下名单 - 向上/向下拨轮
    • 选择文件 - 推拨轮
    • 转到向上的文件夹 - 按BackUp按钮
  2. 菜单
    • 要进入菜单 - 推拨轮
    • 要退出 - 按BackUp按钮
  3. 长键（按3秒）
    • 抬起拨轮 - 刷新文件列表
    • 向下拨轮 - 进入节能状态
    • 按拨轮 - 进入到菜单
    • 按下BackUp按钮 - 重启。和分离所有虚拟机（VHD，RMD，IMA）
  4. 启动密钥（启动时）
    • 抬起拨轮 - 在CD-模式启动
    • 向下拨轮 - 在HDD模式启动了
    • 按拨轮 - 复位加载状态。双模式启动
    • 按下备份按钮 - 在写保护模式启动。

2541 钥匙

  1. 导航
    • 向上/向下列表 - 2 / 8
    • 选择文件 - 5 (or 6, 用于保持装载状态)
  2. 菜单
    • Menu -进入菜单。 （或出口）
    • 4 - 转到上名单
  3. 长键（按3秒）
    • 1 - 进入节能状态
    • 3 - 重新启动IODD
    • 4 - 刷新文件列表
    • 7 - 重启。和分离所有虚拟机（VHD，RMD，IMA）
    • 0 - 重新启动。并暂时禁用写保护
  4. 没有启动密钥

进入节能状态

省电状态：主轴电机停止，液晶显示器的亮度是低的。
CD装载状态被保存
  • (2531) 下滚轮按钮3秒钟
  • (2541) 按1键3秒

选择一个文件

为了保持加载状态，你必须保存的状态。
参考以上的键操作。
  • (2531) #2531 钥匙
    • 如果固件版本为1558或更高，载荷状态会自动保存。
    • 如果没有，你必须手动保存. (#进入省电状态)
  • (2541) #2541 钥匙
    • 如果固件版本低于6（7）9-05，按键6起不了什么作用

安全去除OS

如果IODD的分区是NTFS，然后从主机断开IODD时，此功能是必需的。
NTFS不会立即将数据写入硬盘。
  • 断开连接之前请不要 拆除安全
  • 如果IODD是写保护模式，并显示一条错误消息，然后禁用写保护选项。然后重试此功能。

Initialization

  • the firmware is two sorts. one is NTFS version and other is FAT32/exFAT version.
  • NTFS firmware version is shipped.
  • If you use FAT32 or exFAT Partition, then run FAT Firmware Updater.
  • follow the next steps
  1. assemble the HDD or SSD with iODD
  2. connect the iODD to PC
  3. initialize the drive with MBR
  4. Format the first partition as NTFS. (if the firmware is FAT, then format it as FAT32 or exFAT)
    • At FAT32 there is 4G byte file size limitation. please use that carefully.
  5. create _ISO folder in root folder. (not case sensitive)
  6. copy ISO file to "_ISO" folder. (or create VHD RMD IMA files)
  7. safely remove iODD. ( very Important if NTFS)
  8. If Power Saving mode is active, then disconnect and reconnect the USB cable.
  9. The followings will appear sequentially in LCD
    • "iodd 253(4)1"
    • a file name

Initialize All

If Initialization fails, follow the next steps
  1. disconnect the USB cable.
  2. Get out the HDD from iODD. and Connect directly it to PC.
  3. Initialize it as 'GPT'.
  4. redo Initialization (from the first step). (your HDD is initialized as MBR -> GPT -> MBR).

First Aid

If it has failure suddenly, try one of next steps until the error is clear
  1. (2531) press the Jog Dial and hold, and connect iODD to PC.
  2. try Safely Removal In OS.
  3. Check Disk for iODD ( for Windows)
  4. Rename "_ISO" folder name to other name. Create new _ISO folder, and copy files to this folder. (not moving)
  5. Update with the latest firmware.
  6. Backup the data of iODD, and Initialize All
If there is hardware problem
  1. Reboot the PC
  2. Please change USB cable
  3. Connect iODD to the port of PC back panel.
  4. Try it on another pc
  5. Please change HDD.

Using a Virtual USB Optical Drive (DVD-ROM or Blu-ray ROM)

  1. copy ISO files to "_ISO" folder. (or sub folder)
  2. Safely Remove. (Required for NTFS )
  3. If Power Saving mode is not active , then Go to Power Saving State
    • If "Plug Out ..." message appears, disconnect the iODD.
  4. Connect iODD to a PC. and power on the PC.
  5. (Optional) Make iODD or USB CD-ROM as the first priority of BOOT sequence in BIOS.
  6. If a file has not been selected, then select a ISO file. Selecting a file
  7. If PC don't find booting device (iODD), then reboot the PC. (Ctrl-Alt-Del)

Booting Error

  • Confirm whether the ISO file is able to boot.
  • If your PC is old or does not provide multi LUN, please select CD-MODE (or ODD-MODE).
  • In order to confirm whether the ISO file is able to boot, please try to test it with the validated PC.
  • Although it is bootable ISO file, please confirm whether the result with a USB DVD-ROM is the same
  • If the ISO file is able to boot with USB DVD-ROM and can not boot with iODD, then please use USB Y-CABLE for adding external power.
  • If your laptop has own internal DVD-ROM and iODD does not boot, please disable internal DVD-ROM at BIOS settings. or remove it.

Using a Virtual USB fixed disk drive (Virtual Hard Disk)

  • Fixed VHD file only is supported. (dynamic VHD and VHDx files are not supported)
  • Also fixed VMDK file is supported.
  • Create VHD files directly by "VHD Tool++". ("VHD Tool++" can creates a file without fragment)
  • You can make VMDK by changing name *.VHD to *.VMDK
  • If you select a VHD file (Selecting a file),iODD will be rebooted with CD-MODE and is recognized as USB disk drive.
  • If you want to change to DUAL-MODE or to change Write Protection option, rename the VHD file. refer to "VHD Tool++"
  • Max 4 Virtual Drives are supported at the same time ( Successive selection within 3 seconds)
  1. Create a VHD file using "VHD Tool++" in iODD
  2. If successful, Do safely remove the iODD in OS. ( Very Important to NTFS)
  3. If Power Saving mode is not active, then Go to Power Saving State
    • If Plug Out ... message appear, disconnect the iODD.
  4. Connect iODD to your PC. and power on the PC.
  5. (Optional) Make iODD or USB Device as the first priority of BOOT sequence in BIOS.
  6. If a file has not been selected, then select a VHD file. (Selecting a file)
  7. If PC don't find booting device (iODD), then reboot the PC. (Ctrl-Alt-Del)

Using a Virtual USB Removable Flash Drive (Virtual USB Flash Drive)

  • Almost the same as the above method (Using a Virtual USB fixed disk drive)
  • But the file extension must be changed. VHD -> RMD

Using a Virtual USB Floppy Drive (Virtual FDD)

  • This method is not supported on some computers.
  • Uncompressed floppy image IMA, IMG, BIF, VFD is supported.
  • IMG, BIF, VFD image file extension must be renamed to IMA.
  • Almost the same as the above method
取自“http://zh.iodd.kr/wiki/index.php?title=模板:How_to_use_iODD&oldid=9”